how to deal with 6061 aluminum wall?

In recent years, with the development of technology of aluminum, 6061 aluminum applications are more widely, and now 6061 aluminum is also used as wall decoration. 6061 when aluminum is used as wall decoration, as requested belong metal decoration materials, with the average non-metallic decoration materials are not the same, there are some caveats. Here, we take a look at how to deal with 6061 aluminum wall, the following main points:

1. prominence around 6061 aluminum sleeve cut consistent application of the whole mass, neat edge; dado uniform thickness, and other prominent cheek wall.

2.6061 When you install non-aluminum butt. Lap length should meet the design requirements, may not have thoroughly seam phenomenon.

3. aluminum manufacturers pointed out that when the design No, should adopt aluminum core pulling rivets, intermediate rubber gasket must pad. Aluminum rivets core pulling to control the pitch of 100 ~ 150mm appropriate.

4.6061 aluminum surface should be smooth, clean, color coordination, no discoloration, efflorescence, smudges and significant damage at the sheen.

5. Installation of metal protruding wall facing windowsill, window cover lines and other parts of the projection, the Conference Board noted that the size of aluminum manufacturers should be accurate, smooth and tidy corner, lap size and direction should be correct.

How much do you know the process of pattern aluminum plate?

Top, ingredients: specific trademark pattern aluminum plate alloy produced based on the need to calculate the increase in the amount of various alloy compositions, with a reasonable variety of raw materials.

Second, melting: aluminum plate patterns with a good raw material according to the technical requirements to participate in the melting furnace to melt, and after degassing, the essence of the way the hybrid slag slag melt inside the gas effectively removed.

Third, forging: Pattern aluminum plate smelting aluminum was good at forging a certain technical condition, after deep forging system, cooling forged into a variety of circular casting rods.

Fourth, kneading: and then on kneading, and kneading is shaping the way the profile. The first section will be based on profiles merchandise planning, make a mold, using a kneading machine heated round good casting rod extrusion molding from the mold. Shihai the kneading process using a cooled and hardened after this artificial aging process to complete heat treatment strengthened. Not the same as a trademark heat-strengthened alloy dispose of its heat treatment system is not the same.

Fifth, color: Final is to pattern aluminum plate colored. Before color, first for aluminum oxidation, kneading good aluminum alloy, its surface corrosion resistance is not strong, subject to anodized aluminum surface disposal in order to increase the corrosion resistance, abrasion resistance and surface beautiful degrees.

Titanium sheet metal is larger scale used for Taipei Municipal Stadium's roofing and facades

Recalling the past decade, construction projects in Taiwan, metal roofing and facades of curtain material are commonly used, generally no more than aluminum, stainless steel, iron, copper and other metal materials.

However, Taiwan's larger scale use of titanium sheet metal roofing and facades Curtain case, but it is only a handful. Until July 30, 2013, but only completed in August 2005 Nanjing East Road in Taipei using Dunhua North junction of the first phase of the Taipei Municipal Stadium multifunctional stadium roof project.

The materials used in buildings comes from, and Japan's Mitsubishi Corporation uses 0.3mm + 3.4mmFR + 0.3mm stainless steel combination of 4mm titanium composite plate (TCM), etc. The amount of approximately 7,073m2.

Main Building roof using 0.6mm titanium plates, roof cornices end use

1.5mm titanium plate

Main hall four weeks of 4mm titanium composite panels

Main Building scale sidewall in a 4mm titanium composite panels

Window exhaust spacers 4mm scale mining titanium composite board

Deputy Hall on both sides using 4mm titanium composite panels

Deputy Hall front and pack column with 4mm titanium composite panels

Titanium metal plate is used for the building materials

In building materials, the use of titanium metal, which is used in construction as early on should belong to Japan, for coastal areas or have severe Corrosive environment (hot spring area), permanent buildings (museums, shrines, temples) and so on. But titanium metal building materials is Spain Guggenheim Museum Bilbao extensive use of titanium metal plate building around 1990 in the post, so that titanium building materials by the attention, and then gradually use.

                 Spain Guggenheim Museum Bilbao

Golden Pavilion Temple often foot pavilion was completed in 2003

With about 100m2 titanium plate using AD03 weight 500Kg

Japan's Fuji TV sphere Observatory was completed in 1996

With about 2,800m2 use ND10 titanium plate weight 14 tons

China National Grand Theatre was completed in 2007

Use ND20 weight titanium metal plate with about 43,000m2 65 tons

Taipei Municipal Stadium the first phase of multi-functional stadium was completed in 2005 with about 20,038m2 use ND20 titanium plate weight 50 tons

read more:http://www.detect-metals.com/titanium-metal-plate-is-used-for-the-building-materials/

Do you totally know about Titanium Sheet?

Brands of Titanium Sheet
US brands: GR1, GR2, GR3, GR5, GR7, GR12
Russia brands: BT1-00, BT1-0, BT1-2 etc.
Domestic brands: TA0, TA2, TA3, TA5, TA6, TA7, TA9, TA10, TB2, TC1, TC2, TC3, TC4
A reference standard
1: GB 228 metal tensile test method
2: GB / T 3620.1 titanium and titanium alloys and chemical composition
3: GB / T3620.2 titanium and titanium alloy products and ingredients of the chemical composition of tolerance
4: GB 4698 sea titanium, titanium and alloy chemical analysis method

Titanium implementation of standards
GB: GB / 3621-2007, GB / T13810-2007
American Standard: ASTM B265, ASTM F136, ASTM F67, AMS4928

Titanium production specifications
T 0.5-1.0mm x W1000mm x L 2000-4000mm
T 1.0-5.0mm x W1000-1500mm x L 2000-3500mm
T 5.0- 30mm x W1000-2500mm x L 3000-6000mm
T 30- 80mm x W1000mm x L 2000mm

Titanium sheet Production Status:
Thermal processing status (R)
Cold state (Y)
Annealed condition (M)

Titanium sheet manufacturing process:

Forging metal above the recrystallization temperature forging process carried.
Rolling the hot rolling at a temperature above the recrystallization temperature.
Cold-plastic deformation temperature below the temperature of the rolling process reply.
Annealing: The metal was slowly heated to a certain temperature, maintaining a sufficient time, and then cooling at an appropriate rate (usually slow cooling, and sometimes controlled cooling) the heat treatment process of a metal.
Pickling: The article is immersed in an aqueous solution of sulfuric acid to remove the oxide film such as a metal surface. Pre-treatment or intermediate plating, enamel, rolling and other processes of treatment.

Titanium sheet features:
1. The titanium starting sheet is equivalent to the surface of the oxide film with a good durable wear hair separating agent, using a titanium plate to save the species separating agent, so that the plate peel easily, eliminating the pre-treatment process kinds plate, titanium species board lighter than copper seed plate half.

2. titanium starting sheet is more than three times the life of the copper seed plate, depending on the operating conditions of up to 10-20 years
Copper crystal structure

3. Plate Preparation titanium species dense, smooth surface, good quality.

4. As the titanium species sheet without smearing separating agent, and thus avoid contamination copper electrolyte.

5. The increase productivity to reduce copper production costs, thus better economic benefits.

Aluminum processing industry is facing the impact

In occasion of the upstream aluminum industry production capacity is difficult to curb the excess pressure to the aluminum processing enterprises conduction, which leads to lower consumption of aluminum and aluminum industry profitability a drag.

Number of aluminum processing enterprises are numerous, but the low concentration of production, small-scale production. High level of modern large-scale aluminum group group is not formed. Data show that China's aluminum enterprises currently there are about 1400, of which more than 780 aluminum extrusion plant, aluminum foil plant more than 650, but the large, medium-sized enterprises less than 20%, behind small businesses account for more than 80%, the national aluminum processing enterprises average capacity is only about 25,000 tons / year. ʱ??

In addition, Chinese aluminum processing industry integrated low level of technology, science and technology innovation and weak independent development capabilities, but also one of the reasons the Chinese aluminum exports less competitive.

Market high hopes packaging foil external demand is facing more and more severe test. In 2013 China International Aluminum Industry Exhibition Shanghai International Industrial Materials Exhibition, domestic aluminum production and processing enterprises, said the future will be more difficult export aluminum foil.

By the global slowdown in demand and prices down the impact of Chinese aluminum industry recorded a third quarter net loss of 1.08 billion yuan over the same period recorded a net profit of 555 million yuan last year.

How to enhance the competitiveness of aluminum sheet suppliers

The current intense competition between aluminum sheet suppliers, in order to gain market share in such a market environment and is not easy, but is not no way. For some achievements have been in the market in terms of aluminum sheet suppliers, more should be efforts to enhance competitiveness, otherwise behind.

How to enhance the competitiveness of aluminum sheet suppliers :

1. The production scale, product diversification. Due to the depreciation of production equipment is slower than the average market return excess earnings rate of return, aluminum sheet suppliers operate around the regression average return is the inevitable result, the difference between competitors is reflected in the cost control. Only good cost control, 6061 aluminum price will be more competitive.

2. The sub-sector positioning. Consumption structure and economic development structure is adapted to aluminum, aluminum factory management needs to have a forward-looking position or to emerging sub-sub-industry transformation.

3. The high capacity or capital flexibility. When the sub-sectors appear excess return, the aluminum sheet suppliers can be put into maximizing the expansion of production capacity faster than its competitors to achieve excess returns through capital efficiency, so it's not just "industry how good" or "more than anyone else has money ", but also need to" faster than anyone else. "