How to clean and maintain the buildings of titanium plate?

Any material with the external environment will generate pollution, if not ignored and cleaned regularly, over time will produce is difficult to remove the case, although no corrosion phenomenon, but the appearance is very huge impact. Titanium metal material before cleaning, it is recommended to choose a small area, in order to clean the company's agents to clean, and then wait until it is drier than the rear surface of the original plate, confirmation and then a large area clean, and from top to bottom, the relevant agents pH value should be confirmed, to avoid unnecessary fouling.

1.maintenance mode
(1) When the produce unglued, you can use a sponge or cloth, alcohol, acetone, toluene or a mixture of alcohol and wipe dry when the solution yet, use a clean cloth to scrub.
(2) When generating fingerprints, rain and dust caused by dirt, use a mild detergent or soap. If unable to clear, then remove degumming process to remove it.
(3) titanium surface material and concrete caused by dirt, scrub dilute hydrochloric acid 5%.
(4) titanium zinc sheet metal material and components caused by dirt, scrub dilute hydrochloric acid 15%.
(5) have to be taken after the cleaning water, not residual solution to the material.
(6) The use of the colored titanium metal building materials, not containing
Hydrochloric acid, nitric acid, decontamination powder ingredients to clean, it will cause can not be reinstated.

2.Considerations
(1) titanium material dirt and discoloration of reasons, because of the pollution situation is not the same phenomenon presents different, to be different depending on the status of the clean-up operations one by one, can not summarize a comprehensive clean-up, part of the proposal should be tested against a scrub, dirt observation removal and color condition, and then decide whether to fully clean.
(2) Use a sponge, cotton, nylon, etc. Please hole along parallel grinding titanium wipe clean, the force should be uniform. When the circle with scrub, dirt difficult to remove, but also damaging the surface gloss and light shines colorimeter.
(3) If the dirt is serious, you should avoid using crude bucking (sandpaper, steel wire, etc.), this will not only destroy the titanium light lines, it will undermine the surface, thus causing the dirt.
(4) If the cleaning, use a commercially available cleaners, not only to clean the dirt area, but also around to cleaning, to avoid leaving differences.
(5) When the building clean exterior, if the cleaning liquid splash to the titanium surface, please clean water, dry, if ignored, can cause discoloration of reasons.
(6) When using colored titanium, be sure to provide clean technology manufacturer, to avoid loss of color film and colored titanium.

Titanium metal plate as light weight than steel, structural behavior and representing an aluminum plate excellent workability similar to aluminum metal plate can meet many changes in the exterior of the building structure, with weather resistance can be adapted to the sea and the spa environment, the qualities of the state, the surface is not also cause color status derived maintenance costs, can maintain good color, the color of the material has an industrial development (engaging) and other various features can be used in the multi-building projects.

Types and applications of titanium plates

Do home space looks luxurious texture, you do not have to use explicit and flamboyant materials to create. Titanium plate can often be seen being used in a department store or boutique counters, elevators, cars, automatic doors or escalator, because of its different substrate surface (wool yarn, mirror, random pattern, fog beads), can show different feeling, recently it has more and more designers bold use of space in the home!

Very early use of titanium in industrial buildings, based on the way the physical vacuum ion plating titanium nitride (tin) process in the material, the most common is plated on stainless steel, of course, can also be coated in hard substrates such as tiles or aluminum, copper and the like. Antioxidant, wear and do not fade, etc., and therefore more suitable for use in wet environments, covered the kitchen or bathroom. Compared to chemical plating plate, longer service life, because the whole production process is based on physical principles of processing, harmless, zero pollution, also known as green coated.
Titanium plate variety, there are titanium bristles panel, titanium and titanium mirror panels random pattern plate and titanium matte bead board, under the designer's ingenuity through, different surfaces can exhibit different spatial performance in the use, it can also bring out the lines of the neat, geometric shapes and other fun feeling.

Currently, titanium materials are often used in indoor public spaces, such as restaurants, living room or entrance. However, if the license on the budget, big also be used in the locker room or bedroom, or design on the desktop. Use titanium mirror panels, the reflective effect, can make visual space becomes avant-garde. If the large-scale use titanium mirror panels, can easily be room reflections, creating a visual phantom space twice. Titanium bristles plate fog or mist flu mix of warm wood bead board, you can have both "cold" and "warm" feel.

Even with the door frame or sheet closing sapwood, because of single lines and other building materials also make home become structured simple and neat. I want to create a luxurious texture, golden titanium plate using the amplifier and gorgeous coexist. But special titanium production process, so compared to other materials, the price is slightly higher. In addition, the trend of the impact of design changes, in addition to different styles panel, the panel after getting physical vacuum plating (pvd), the titanium plate also has a new style rendering. From silver, copper, gray, to black, champagne or rose gold, so the cold becomes lively sense of fun, create a rich visual experience. Regardless of the basic style or color titanium plate, you can decorate a dream tide space.

Titanium is widely used in the electroplating industry

Electroplating tank titanium anode baskets, such as Tong Gang, nickel cylinder, tin ball tin cylinder (surface ruthenium, rhodium-plated); gold cylinder insoluble anodes (surface plated platinum, ruthenium or rhodium-plated); heating pipe / (sometimes also into a hot pen); a condenser, and some of the equipment housing!

As a precious metal titanium, titanium and titanium plate in circuit board plating production enterprise is widely used, with excellent mechanical properties and excellent specific strength (strength / density ratio), more superior performance titanium; titanium Mechanical properties of the alloy by the following factors: the type of the alloy, and the addition amount ratio, processing methods, processing capacity, heat treatment conditions and the like prior to use. For example titanium shafts, titanium multilayer inner main black / brown treatment, plywood Desmear swell, except plastic tank (sometimes alkaline chemistry in addition to copper sump also apply, but multi-purpose stainless steel 316.

Titanium also has the following advantages:

1. A high temperature characteristics:

At high temperatures, tensile strength and excellent creep properties, up to 300 degrees around titanium metal, titanium alloys at 500 degrees still has a stable strength;

2. low-temperature characteristics:

At absolute zero, no embrittlement, still has good fatigue strength and fracture toughness;

3. anti-fatigue toughness:

But after welding heat affected zone significantly decrease fatigue strength phenomena;

4. corrosion resistance, acid and alkali resistance:

The corrosion resistance of titanium depends on the stability of the oxide film on the surface

Titanium Basics Introduction

Due to the excellent corrosion resistance of titanium, titanium is widely used in petroleum, chemicals, salt,; the relevant pharmaceutical, metallurgy, electronics, aviation, aerospace, marine and other.

Titanium is a metal having a strong tendency to passivation, and oxidizing in air or a neutral aqueous solution can quickly generate a stable oxidation protective film, even if the film is destroyed for some reason, can quickly resume automatically. Thus Titanium has excellent corrosion resistance in oxidizing, neutral medium.

Due to the huge passivation properties of titanium, in many cases when in contact with dissimilar metals does not accelerate corrosion, which may accelerate the corrosion of dissimilar metals. When such a low concentration of non-oxidizing acids, if Pb, Sn, Cu, or Monel and titanium-contact electrical coupling, accelerate corrosion of these materials, and titanium is not affected. In hydrochloric acid, when brought into contact with the titanium low carbon steel, since the surface of titanium nascent hydrogen, destroys the oxide film of titanium, titanium not only causes hydrogen embrittlement, and to accelerate the corrosion of titanium, titanium this may be due to hydrogen is highly activity due.

Titanium iron content of certain media affect corrosion resistance, iron number of reasons in addition to the reasons of raw materials, are often contaminated iron welding weld penetration, so the local iron bead increased, which When corrosion has an uneven nature. Used iron pieces to support titanium equipment, iron titanium contact surface iron contamination is almost inevitable in accelerated corrosion of iron contamination zone, especially in the presence of hydrogen. When the surface of the titanium oxide film contamination of mechanical damage, infiltration of hydrogen on metal, depending on the temperature, pressure and other conditions, the hydrogen generating corresponding diffusion, which makes titanium produce different degrees of hydrogen embrittlement. Therefore titanium at moderate temperatures and moderate pressure and hydrogen used in the system to avoid surface iron contamination.

Because titanium in hydrocarbons corrosion resistance is very good, even when containing acid and chloride impurities is also very good. Therefore, in the organic chemical industry Titanium is also widely used, such as PTA (purified terephthalic acid), PVA (Vinylon), etc. Titanium has excellent corrosion resistance in seawater, it is also widely used titanium offshore oil drilling platform, desalination and other marine areas.

Titanium and titanium alloy manufacturing technology

Since the cost titanium alloy is very high, in order to make cost reduction to lower the price increases throughout the metal alloy materials market competitiveness. It is widely believed Titanium has incomparable superiority of other material, but the price of titanium often consumers (especially the car manufacturers) prohibitive, appears low quality titanium will certainly help expand the application of titanium and titanium alloys.

    From the present situation of the development of applications and titanium processing technology, the plastic processing technology of titanium and titanium alloys in the future will be towards the following directions:

    (1) high-performance, namely the development of the use of higher temperatures, higher than the strength higher than the modulus, corrosion resistance and abrasion resistance and better alloys.

    (2) multi-functional, namely the development of a variety of special features and use of titanium alloys, such as high damping, low expansion, constant resistance, high resistance, resistance to electrolytic passivation and hydrogen storage, shape memory, superconductivity, low modulus biological medical and other alloys, in order to make titanium and titanium alloys to further expand the application.

    (3) to deepen the study of traditional alloys, through equipment and process improvements, improved performance of existing practical alloys, expanding the use of conventional alloys.

    (4) the use of advanced processing technology, processing equipment, large-scale, continuous, continuous processing technology development, direct rolling technology, cold forming technology and productivity performance of titanium alloy, the yield and product near net shape technology to improve
ʱ??
    (5) cost of the development of free alloy containing less noble metal elements, add iron, oxygen, nitrogen and other low-cost elements, shaping the development of easy processing, easy cutting, alloying elements and inexpensive titanium master alloy. Developed to maximize the use of titanium material crippled, maimed titanium improve recycling rates. This is particularly important to reduce the cost of civil Titanium.

    (6) the use of advanced computer technology to simulate the deformation of the workpiece machining process, forecasting the evolution of the microstructure of the metal, and even predict the mechanical properties of the final product (yield strength, tensile strength, elongation and hardness, designed or modified for mold, tooling; analysis and processing test results, reducing test, improve work efficiency and reduce development costs.

how to deal with 6061 aluminum wall?

In recent years, with the development of technology of aluminum, 6061 aluminum applications are more widely, and now 6061 aluminum is also used as wall decoration. 6061 when aluminum is used as wall decoration, as requested belong metal decoration materials, with the average non-metallic decoration materials are not the same, there are some caveats. Here, we take a look at how to deal with 6061 aluminum wall, the following main points:

1. prominence around 6061 aluminum sleeve cut consistent application of the whole mass, neat edge; dado uniform thickness, and other prominent cheek wall.

2.6061 When you install non-aluminum butt. Lap length should meet the design requirements, may not have thoroughly seam phenomenon.

3. aluminum manufacturers pointed out that when the design No, should adopt aluminum core pulling rivets, intermediate rubber gasket must pad. Aluminum rivets core pulling to control the pitch of 100 ~ 150mm appropriate.

4.6061 aluminum surface should be smooth, clean, color coordination, no discoloration, efflorescence, smudges and significant damage at the sheen.

5. Installation of metal protruding wall facing windowsill, window cover lines and other parts of the projection, the Conference Board noted that the size of aluminum manufacturers should be accurate, smooth and tidy corner, lap size and direction should be correct.

How much do you know the process of pattern aluminum plate?

Top, ingredients: specific trademark pattern aluminum plate alloy produced based on the need to calculate the increase in the amount of various alloy compositions, with a reasonable variety of raw materials.

Second, melting: aluminum plate patterns with a good raw material according to the technical requirements to participate in the melting furnace to melt, and after degassing, the essence of the way the hybrid slag slag melt inside the gas effectively removed.

Third, forging: Pattern aluminum plate smelting aluminum was good at forging a certain technical condition, after deep forging system, cooling forged into a variety of circular casting rods.

Fourth, kneading: and then on kneading, and kneading is shaping the way the profile. The first section will be based on profiles merchandise planning, make a mold, using a kneading machine heated round good casting rod extrusion molding from the mold. Shihai the kneading process using a cooled and hardened after this artificial aging process to complete heat treatment strengthened. Not the same as a trademark heat-strengthened alloy dispose of its heat treatment system is not the same.

Fifth, color: Final is to pattern aluminum plate colored. Before color, first for aluminum oxidation, kneading good aluminum alloy, its surface corrosion resistance is not strong, subject to anodized aluminum surface disposal in order to increase the corrosion resistance, abrasion resistance and surface beautiful degrees.

Titanium sheet metal is larger scale used for Taipei Municipal Stadium's roofing and facades

Recalling the past decade, construction projects in Taiwan, metal roofing and facades of curtain material are commonly used, generally no more than aluminum, stainless steel, iron, copper and other metal materials.

However, Taiwan's larger scale use of titanium sheet metal roofing and facades Curtain case, but it is only a handful. Until July 30, 2013, but only completed in August 2005 Nanjing East Road in Taipei using Dunhua North junction of the first phase of the Taipei Municipal Stadium multifunctional stadium roof project.

The materials used in buildings comes from, and Japan's Mitsubishi Corporation uses 0.3mm + 3.4mmFR + 0.3mm stainless steel combination of 4mm titanium composite plate (TCM), etc. The amount of approximately 7,073m2.

Main Building roof using 0.6mm titanium plates, roof cornices end use

1.5mm titanium plate

Main hall four weeks of 4mm titanium composite panels

Main Building scale sidewall in a 4mm titanium composite panels

Window exhaust spacers 4mm scale mining titanium composite board

Deputy Hall on both sides using 4mm titanium composite panels

Deputy Hall front and pack column with 4mm titanium composite panels

Titanium metal plate is used for the building materials

In building materials, the use of titanium metal, which is used in construction as early on should belong to Japan, for coastal areas or have severe Corrosive environment (hot spring area), permanent buildings (museums, shrines, temples) and so on. But titanium metal building materials is Spain Guggenheim Museum Bilbao extensive use of titanium metal plate building around 1990 in the post, so that titanium building materials by the attention, and then gradually use.

                 Spain Guggenheim Museum Bilbao

Golden Pavilion Temple often foot pavilion was completed in 2003

With about 100m2 titanium plate using AD03 weight 500Kg

Japan's Fuji TV sphere Observatory was completed in 1996

With about 2,800m2 use ND10 titanium plate weight 14 tons

China National Grand Theatre was completed in 2007

Use ND20 weight titanium metal plate with about 43,000m2 65 tons

Taipei Municipal Stadium the first phase of multi-functional stadium was completed in 2005 with about 20,038m2 use ND20 titanium plate weight 50 tons

read more:http://www.detect-metals.com/titanium-metal-plate-is-used-for-the-building-materials/

Do you totally know about Titanium Sheet?

Brands of Titanium Sheet
US brands: GR1, GR2, GR3, GR5, GR7, GR12
Russia brands: BT1-00, BT1-0, BT1-2 etc.
Domestic brands: TA0, TA2, TA3, TA5, TA6, TA7, TA9, TA10, TB2, TC1, TC2, TC3, TC4
A reference standard
1: GB 228 metal tensile test method
2: GB / T 3620.1 titanium and titanium alloys and chemical composition
3: GB / T3620.2 titanium and titanium alloy products and ingredients of the chemical composition of tolerance
4: GB 4698 sea titanium, titanium and alloy chemical analysis method

Titanium implementation of standards
GB: GB / 3621-2007, GB / T13810-2007
American Standard: ASTM B265, ASTM F136, ASTM F67, AMS4928

Titanium production specifications
T 0.5-1.0mm x W1000mm x L 2000-4000mm
T 1.0-5.0mm x W1000-1500mm x L 2000-3500mm
T 5.0- 30mm x W1000-2500mm x L 3000-6000mm
T 30- 80mm x W1000mm x L 2000mm

Titanium sheet Production Status:
Thermal processing status (R)
Cold state (Y)
Annealed condition (M)

Titanium sheet manufacturing process:

Forging metal above the recrystallization temperature forging process carried.
Rolling the hot rolling at a temperature above the recrystallization temperature.
Cold-plastic deformation temperature below the temperature of the rolling process reply.
Annealing: The metal was slowly heated to a certain temperature, maintaining a sufficient time, and then cooling at an appropriate rate (usually slow cooling, and sometimes controlled cooling) the heat treatment process of a metal.
Pickling: The article is immersed in an aqueous solution of sulfuric acid to remove the oxide film such as a metal surface. Pre-treatment or intermediate plating, enamel, rolling and other processes of treatment.

Titanium sheet features:
1. The titanium starting sheet is equivalent to the surface of the oxide film with a good durable wear hair separating agent, using a titanium plate to save the species separating agent, so that the plate peel easily, eliminating the pre-treatment process kinds plate, titanium species board lighter than copper seed plate half.

2. titanium starting sheet is more than three times the life of the copper seed plate, depending on the operating conditions of up to 10-20 years
Copper crystal structure

3. Plate Preparation titanium species dense, smooth surface, good quality.

4. As the titanium species sheet without smearing separating agent, and thus avoid contamination copper electrolyte.

5. The increase productivity to reduce copper production costs, thus better economic benefits.

Aluminum processing industry is facing the impact

In occasion of the upstream aluminum industry production capacity is difficult to curb the excess pressure to the aluminum processing enterprises conduction, which leads to lower consumption of aluminum and aluminum industry profitability a drag.

Number of aluminum processing enterprises are numerous, but the low concentration of production, small-scale production. High level of modern large-scale aluminum group group is not formed. Data show that China's aluminum enterprises currently there are about 1400, of which more than 780 aluminum extrusion plant, aluminum foil plant more than 650, but the large, medium-sized enterprises less than 20%, behind small businesses account for more than 80%, the national aluminum processing enterprises average capacity is only about 25,000 tons / year. ʱ??

In addition, Chinese aluminum processing industry integrated low level of technology, science and technology innovation and weak independent development capabilities, but also one of the reasons the Chinese aluminum exports less competitive.

Market high hopes packaging foil external demand is facing more and more severe test. In 2013 China International Aluminum Industry Exhibition Shanghai International Industrial Materials Exhibition, domestic aluminum production and processing enterprises, said the future will be more difficult export aluminum foil.

By the global slowdown in demand and prices down the impact of Chinese aluminum industry recorded a third quarter net loss of 1.08 billion yuan over the same period recorded a net profit of 555 million yuan last year.

How to enhance the competitiveness of aluminum sheet suppliers

The current intense competition between aluminum sheet suppliers, in order to gain market share in such a market environment and is not easy, but is not no way. For some achievements have been in the market in terms of aluminum sheet suppliers, more should be efforts to enhance competitiveness, otherwise behind.

How to enhance the competitiveness of aluminum sheet suppliers :

1. The production scale, product diversification. Due to the depreciation of production equipment is slower than the average market return excess earnings rate of return, aluminum sheet suppliers operate around the regression average return is the inevitable result, the difference between competitors is reflected in the cost control. Only good cost control, 6061 aluminum price will be more competitive.

2. The sub-sector positioning. Consumption structure and economic development structure is adapted to aluminum, aluminum factory management needs to have a forward-looking position or to emerging sub-sub-industry transformation.

3. The high capacity or capital flexibility. When the sub-sectors appear excess return, the aluminum sheet suppliers can be put into maximizing the expansion of production capacity faster than its competitors to achieve excess returns through capital efficiency, so it's not just "industry how good" or "more than anyone else has money ", but also need to" faster than anyone else. "

The widely applications of mirror aluminum

On the market of aluminum plate, the mirror aluminum is the most widely used application, which is due to the superiority of its own decision. Mirror aluminum has excellent heat resistance, the reflectivity of the surface is relatively good, but also has strong corrosion resistance. Here, we take a look at mirror aluminum unexpected purposes.

Mirror aluminum with excellent weather resistance, corrosion resistance of galvanized steel is 3 to 6 times. Mirror aluminum can reflect 80% of the incoming heat. Mirror aluminum have a strong chemical corrosion. The mechanical strength consistent with its mirror aluminum substrate.

1. Outdoor Products: mirror aluminum processed products can be used as barbecue pits, charcoal, collection / exhaust port, smokestack.

2. Household products: ovens, microwave ovens, rice cookers, multi-functional pot, slow cooker, toaster, electric water heaters, electric thermos, disinfection cabinet, air conditioners, heat exchangers, electric heating, lighting and so on. Kitchen utensils: frying pan, kettle, hotplate.

3. Automotive: aluminum mirror processed into the muffler, exhaust pipes, tanks, heat shield, reactor components and manifolds enclosures. Construction, agricultural and mining machinery: diesel muffler and heat shield, lawnmowers and other garden machinery muffler.

Aluminum Alloy grades, the material and the use

Aluminum alloy is a common approximation material, from 1000 series aluminum, the high hardness of 7075 aluminum alloy series, introduces many common alloy grades, the material uses.

1050: food, chemical and brewing industries squeeze coil with a variety of hose, fireworks powder.

1060: requirements for corrosion resistance and formability of the occasion, but do not ask for strength, chemical equipment is its typical use.

1100: for the processing need to have good formability and high corrosion resistance, but are not required to have high strength parts and components, such as chemical products, food industry equipment and storage containers, sheet metal parts, deep drawing or spinning hollowware, welding parts, heat exchangers, printing plates, plate, reflective devices.

2024: aircraft structures, rivets, missile components, the card wheel hub, propeller components and various other structures.

3003: for the processing need to have good formability, high corrosion resistance and good solderability component parts, or both of these performance requirements and the need to have a high strength alloy than 1XXX work, such as kitchen utensils, food and chemical products processing and storage devices, tank transport of liquid products, cans, sheet metal processing to various pressure vessels and piping

3004: aluminum cans cans, requiring higher strength than the 3003 alloy parts, chemical products and storage equipment, sheet metal parts, building processing parts, construction tools, a variety of lighting components

5050: sheet can be used as refrigerators and refrigerator lined plate, automobile pipe, tubing and agricultural irrigation pipe; also can be processed plate, pipe, bar, profile and wire, etc.

5052: This alloy has good forming properties, corrosion resistance, can be candles, fatigue strength and static strength medium, for the manufacture of aircraft fuel tanks, pipelines, and transportation vehicles, ship sheet metal parts, instruments, lights bracket and rivets , metal products

5056: magnesium alloys and cable sheathing rivets, zippers, nails, etc; clad aluminum wire is widely used in the processing of agricultural insect traps cover, and the need for high corrosion resistance of other occasions

5083: for the need to have high corrosion resistance, good weldability and moderate-intensity situations, such as ships, cars and airplanes plate welded; be strictly fireproof pressure vessels, refrigeration equipment, tower, drilling equipment, transportation transportation equipment, missile components, armor, etc.

5086: for the need to have high corrosion resistance, good weldability and moderate-intensity situations, such as ships, automobiles, aircraft, cryogenic equipment, tower, drilling equipment, transportation equipment, missile parts and so on deck

6061: requires a certain strength, weldability and high corrosion resistance of a variety of industrial structural, such as the manufacture of trucks, tower buildings, ships, trams, fixtures, machinery parts, precision machining and other tubes, rods, shaped timber used, Sheet

6063: building profiles, as well as irrigation pipes for vehicles, stand, furniture, fencing and other materials used in extrusion

7005: extruded material for the manufacture of both a high strength but also have high fracture toughness of welded structures such as trusses transportation vehicles, rods, container; large heat exchangers, and can not be solid melting process after welding components; also used in the manufacture of sports equipment such as tennis rackets and baseball bats

7050: aircraft structural parts with plate, extrusions, forgings and die forgings. Manufacture of such parts of the alloy requirements are: anti-spalling corrosion, stress corrosion cracking, fracture toughness and fatigue resistance are high

7072: air conditioners and special thin strip of aluminum foil; 2219,3003,3004,5050,5052,5154,6061,7075,7475,7178 alloy plate and pipe cladding layer

7075: for the manufacture of aircraft structures and futures He demanded high strength, corrosion resistance and strong high-stress structural parts, mold manufacturing

7175: for high-strength structural use of forged aircraft. T736 material has good overall performance, namely strength, resistance to exfoliation corrosion and stress corrosion cracking resistance, fracture toughness, fatigue strength are higher

7178: for the manufacture of aerospace vehicle requirements compressive yield high strength parts

7475: body and not by the clad clad aluminum plate, the wing skeleton, stringers and so on. Other have both high strength but also have high fracture toughness of parts

7A04: aircraft skin, screws, and the force components such as beam stringers, bulkheads, wing ribs, landing gear, etc.

The extensive use of aluminum plates

Detect-Metals tell you the extensive use of aluminum plates:

1. Lighting

2, solar reflective sheet

3, building exterior

4, interior decorating: ceilings, walls, etc.

5, furniture, cabinets

6, Elevator

7, signs, nameplates, luggage

8, automotive interior and exterior decoration

9. aluminum interior products: such as photo frames

10, household appliances: refrigerators, microwave ovens, audio equipment and other

11. The aerospace and military aspects, such as China's current large aircraft manufacturing, the Shenzhou series spacecraft, satellites and so on.

12, machine parts

13, mold manufacturing

14, chemical / thermal insulation pipe coating

What conditions are more suitable for aluminum sheet storage？

First, to ensure storage environment must be in a ventilated, dry environment storage, known to belong to the non-ferrous metal aluminum sheet, will produce oxidation reflect the future, if in contact with water, so it destroyed the surface, resulting in surface quality is affected, so a drying The environment is the basic condition for storing aluminum sheet.

Sealing performance package, usually aluminum sheet at the factory will take waterproof packaging, packaging that has the preservative, it is recommended that users do not destroy the packaging, the package is suitable for long-term storage use. If you have certain conditions, then you can talk after use The aluminum sheet was also true of the packaging.

aluminum sheet is mainly used in metal wall side, and therefore the metal walls of the aluminum sheet curtain has accounted for a dominant position in the metal walls, light, reducing the load of the building, high-rise building offers a good selection conditions; waterproof, anti-pollution, anti- excellent corrosion resistance, to ensure that the building exterior surface lasting Changxin; processing, transportation, installation and construction are all relatively easy to implement, its widely used to provide strong support; diversity of colors can be combined and processed into different external shape, expand architects design space; high performance and low cost, easy to maintain, with a long service life, fully meet the market requirements and therefore, the aluminum sheet curtain wall as an architectural form high-impact, fully received by the marketing recognition.

6061 aluminum plate superior performance

6061 aluminum plate belong to 6XXX serise alloy aluminum , the main alloying elements are magnesium and silicon. Products with moderate strength, good corrosion resistance, weldability, oxidation is better, is widely used in trucks, tower buildings, ships, trams, rail vehicles with a certain strength and high corrosion resistance of industrial structure, such as manufacturing and so on.

From the production process point of view, from 6061 alloy semi-continuous casting, homogenization, sawing, milling surface, clad, heating, hot rolling, annealing, cold rolling, annealing, cold rolling, solution treatment, aging treatment, to cut cutting, leveling, inspection, oiled packaging of this series of process, constitute a complete production step 6061 aluminum sheet .

6061 aluminum production process has been very mature now, at present, the domestic production of the factory in 6061 alloy have dozens, while Detect-Metals is one representative leader.

why pattern aluminum appears bleaching?

Some construction units to deceive the owners to indoor plate posing aging, corrosion-resistant high-quality fluorocarbon plate, get unreasonable profit, thus forming aluminum used on the project presented serious discoloration, discoloration.

As we all know about pattern aluminum , when purchase pattern aluminum, we often see discoloration,bleaching, how did it happened ? Let's Technical department to explain it. Striped aluminum discoloration, bleaching, mainly because of the formation of the plate inappropriate choice.

Aluminum plate with a plate divided into indoor and outdoor panels, outer coating two plates are not the same, determines its application is not the same situation. Interior plate used, and its appearance is usually sprayed resin coating, this coating habit not outdoor harsh natural environment, if used in outdoor, nature will accelerate the aging process, causing the appearance of discoloration decolorization outdoor outer coating aluminum composite panel is usually used anti-aging, anti-ultraviolet light to strong bomb grease coated polyvinyl fluoride layer, the price of this sheet is expensive.

What is Aluminum Coils？

Aluminum coils by rolling after casting machine, pull the corners processing, For the shears metal commodities.

How many types does aluminum coils have?

Aluminum coils are widely used in electronics, packaging, construction, machinery, etc., Chinese aluminum coil production company more prosperous country has caught up the production process, on the basis of aluminum coil aluminum coil aluminum-rich metallic element is not the same, aluminum coil can roughly divide for the nine categories, that is capable of sub-nine series, the following about the gradual introduction:

1, the 1000 series: the representative of 1,050,106,010,701,000 series aluminum is also known as pure aluminum, in all series, 1000 series aluminum content attributed most of a series.

2, the 2000 series aluminum sheet: representative of 2A16 (LY16) 2A06 (LY6) 2000 series aluminum is characterized by high hardness, during which the copper-origin content, about 3-5% or so.

3, the 3000 series aluminum sheet: representative of the main 3003 3003 3A21. It can be called anti-rust aluminum China 3000 series aluminum production process is more excellent.

4, the 4000 series aluminum: representatives 4A01 4000 series aluminum attributed to higher silicon content.

5, the 5000 series: the representative 5052.5005.5083.5A05 series.

6, the 6000 series: 6061 on behalf of the first two elements are rich in magnesium and silicon, it is focused on the 4000 series and 5000 series of the strengths of 6061, a cold finished aluminum casting goods for opposition corrosion, oxidation and demanding applications.

7, 7000: 7075 on behalf of the primary zinc-rich

8, 8000 Series: more commonly attributed to other series for 8011

9, 9000: attributed to spare series, science and technology is now so prosperous, in order to respond to other alloying elements aluminum-rich presentation, the International Federation of special aluminum strip marked 9000 as the backup series, waiting for another new species to fill the 9000 presentation series blank.

Aluminum surface treatment on problem solving approach

Use aluminum plate quality is not very good, too many impurities will be mixed inside take peeling in aluminum plate,the aluminum sheet after shot blasting treatment, the aluminum oxide layer above will be destroyed. Can not handle very clean, remained part of the oxide layer on top of.

Shot in order to make work further compaction, usually every square centimeter of power by force of 3 kg around, if  itself die-casting have quality problems, such as pores, bubbles, cold shut, playing in real time will be blasting produce peeling phenomenon, which is the same concept of non-casting from the peeling to separate.

Of the above questions is currently no effective method, you can learn basic processing pathways:

1, will be  improve the quality of the work piece;

2, lower pressure blasting;

3 Shot from the skin site to be polished, such as sanding the bottom of the problem, you can re-throw.

How to handle the problems of aluminum sheet?

Aluminum sheet in the production process of rendering a lot of harm, scratches, rubs and so on, which is when the aluminum plate from flowing out of the membrane pores in the process will be presented, as well as perhaps in the future use of the processing takes place in the process this is only the appearance of scars, the main reason is there are several causes of.

    1. In the production process, from swing bed generals dragged down abrasions aluminum sheet formation.

    2. The transport process of aluminum sheet, the mutual information between the amount of conflict will be deformed.

    3. In the time-division operation, there are some solid debris belt material, and then to touch the aluminum sheet after a certain hazard occurs.

    4. Before the aluminum plate tracks, present some debris on the track, perhaps within the graphite hard object, will be on the aluminum sheet forming a certain hazards.

    5. When will the bumps in the process of discharging speed can not be too soon, too fast to put the aluminum sheet on the bed.

    These are some of the production will be presented on these abrasions nor is not resolved, following the introduction of several solutions.

    1. The production process must be strengthened demand for ingot quality control.

    2. The aluminum sheet material in the box seat must be placed to be reasonable, so that we can be useful to reduce conflict.

    3. nitride mold timing must demand protection, we can improve the quality of the mold.

    4. Do not because it is not Reflections aluminum plate gently, and the best is not free to drag aluminum sheet. Be sure to use between aluminum sheet and aids.

    5. soft things apart, touch less and assistive devices can be useful to fall hazards.

how can we distinguish the fake or real aluminum alloy fastly?

Since more and more aluminum alloy products appear after another, it's not easy to tell when we select it, a lot of unscrupulous manufacturers took the opportunity to make trouble, aluminum alloy mixed fish heads on the market, real to the enemy, indeed a headache for consumers. But how can we distinguish the fake or real aluminum alloy fastly?

1. There are two sides of aluminum alloy:sub-sided and single-sided.

2. At the time of purchasing it,you need to observe its surface and color, whether the appearance is smooth, the color is gorgeous.

3. aluminum alloy glue seam neat, decorative aluminum plate when building exterior, between the plates must usually have a slit width.

4. If the appearance of aluminum alloy with deform and dark,these are defective.

5. You can analyze aluminum alloy, the primary problem is on the bottom of the aluminum plate , the dealer would recommend that you purchase the underlying data is the high-density wood panels and more similar. It's outdoor use, their life is very weak, will deform easily after wind, sun and rain. The underlying data are already deformed, do not be fooled by dealers, must hold what you want to buy.

How to clean pattern aluminum plate professionally?

Pattern aluminum plate in life is becoming more common, and the role of pattern aluminum is also growing, after the washing process will become more beautiful pattern aluminum alloy in the production process will often appear loose ingot or blowhole and other defects, to the production process of a lot of trouble. Following small and you a brief introduction pattern aluminum plate washing deal with it, how to be more professional washing pattern aluminum plate.

Start porosity is concerned, it is mainly among aluminum ingot circular hole, the reason is mainly formed when dissolved gas is always in a state of saturation, and the melt, there are still a lot of non-metallic inclusions It slows things, so that the gas in the process of casting floating rate, bubbles will remain in the pores of the ingot.

Loose ingot form factors are two: First, there is no removal of loose melt gases; the second is a loose contraction generated when it is related to gas and melt, generally when we conduct analysis mainly based on gas content of the melt and the casting speed.

In fact, we can also use a liquid feeding mode, so it reduces the metal in the furnace residence time, can make the inside of the gas furnace in the continuous saturation effect to get a good release and decomposition, but also good control generation of impurities, reduce non-metallic slag material.

1, after alkaline etching, the aluminum plate surface pattern will be left Dalian alkaline etching grooves film, which we call water alkaline etching after. Pattern aluminum plate base after etching is more difficult to clean, and first of all we want in favor of cleaning products point of view, the first tank to maintain the temperature of the water and alkaline water is not going to replace. After washing twice, in order to make a better cleaning effect, we can be appropriately stirred. After washing twice watching work How much amount may be, it can not handle the overflow.

2, it is necessary to go through at least two water washing step is called neutralized. This washing we recommend using circulating water cleaning, doing so in order to protect normal oxidation tank when, because in and the nitric acid tank, if it is brought into the oxidation tank, then there may not form an oxide film, or an increase in the oxidation tank impurities, this will accelerate the aging of the oxidation tank.

3, a simple two washing, washing after chemical polishing after chemical polishing will be from some residual liquid, in order to better clean, small second sink recommend using circulating water, the first water tank maintained at a temperature on the line.

bulk roll titanium plate industry successfully

Commercially pure titanium plate widely used in military, medical equipment, aerospace, marine and other industry research, only a few domestic mills have a production capacity of titanium volume. The past two years, rising LIANGANG innovation, the successful development and production LG280VK, LG960QT other high-end products.

Among them, titanium for low temperature, soft, and high surface quality requirements, ongoing technical research, technical barriers to break, in the heating system, rolling technology, size control, surface quality and other aspects have made a major technological breakthrough, thickness control batch reach 3.0mm, the thinnest down to 2.65mm, the production parameters and specifications of the leading domestic level.

2017 Transfer of the demand for aluminum composite materials, or up to 850,000 tons

Heat aluminum composite materials (aluminum sheet, aluminum strip, aluminum foil, etc.) primarily for automotive heat transfer systems, household appliances, machinery and equipment as well as thermal power stations air cooling system. By the stimulation of downstream industries, the global heat transfer aluminum composite material in 2006--2014 years, the average growth rate of 6.1 percent and reached 1.38 million tons in 2014, up 4.5 percent year on year, but lower than the 13-year fell 1.1%.

As the world's leading consumer of heat aluminum composite material, the total demand in China in 2014 was 591,900 tonnes, mainly due to the increase in the automotive industry light machinery and equipment needs. Is expected to 2017, China's aluminum composite heat will reach 850,000 tons.

At present, China's heat transfer aluminum composite manufacturers are mostly foreign companies and joint ventures, it contributed more than 60% of total production. In contrast, Chinese enterprises are restricted by factors such as lack of technical support, small-scale enterprises, leading to a lack of market competitiveness.

A wholly owned subsidiary Granges-- Oklahoma, specializing in thermite composites business, now has annual production of 210,000 tons. Granges heat aluminum (Shanghai) Co., Ltd., is the company's production base is located in China, now has annual production of 120,000 tons. Future, the company plans to build a second production base in China aluminum heat.

Novelis Inc. is the United States the most important heat-aluminum composite material manufacturers. In October 2014, the company is located in China's first automotive aluminum heat treatment plant has been completed and began operating, the plant has a 120,000 per year.

30mm thick electron beam welding titanium TA1 success

Pangang Group Steel Institute heavy rail and rail colored homes cooperation with the Guangzhou Institute of Panzhihua responsible for 30mm thickness titanium sheet metal TA1 electron beam welding process test, recently in Beijing Ai Jiemo Robot Systems Ltd. uses German SST's vacuum electron beam welder welding first success, good weld quality, appearance, the advantages of small heat-affected zone, indicating that production TA1 Panzhihua titanium plate has good weldability.

The successful welding 30mm thick titanium plate TA1 marks Pangang major project "titanium and titanium alloy products applied technology research" has made progress stage for the future Panzhihua titanium and titanium alloy products in the aerospace, marine engineering, energy and chemical and many other fields of application and marketing laid a good foundation.

TC4 titanium rod forging process analysis

Large deformation resistance of titanium alloy, chemically active, thus forging process has special problems and difficulties. First, the microstructure and properties of titanium forgings for forging thermal parameters are very sensitive. Titanium forging temperature range is relatively narrow in the forging process, with the increase of strain rate, its deformation resistance increased significantly, showing a strong strain rate sensitivity. Second, the thermal conductivity of titanium alloys is poor, in the forging process prone to localized overheating, resulting in a large temperature difference between inside and outside, inside and outside the degree of deformation of the blank exacerbate uneven distribution, resulting in cracking the forging process, and in severe cause product obsolescence. Therefore, studying the effects of different forging process on the microstructure and mechanical properties of titanium alloys, to seek a reasonable forging process to forming titanium forgings production has important practical significance.

TC4 titanium alloy have excellent performance in the aerospace, automotive and medical and other fields has been widely used, is the most widely used as a two-phase α + β type titanium alloy. Scholars of the various properties and processing technology titanium launched a lot of research, however, the system of different forging process on TC4 alloy microstructure and mechanical properties of a few. Researchers studied the β forging, forging close β and (α + β) two-phase region forging affect three different bars forging process on microstructure and mechanical properties of TC4 titanium alloy microstructure, more optimization program with a view to forging process selected for Production TC4 titanium alloy forgings to meet the requirements to provide a reference.

TC4 alloy material size experiment is Φ100mm × 450mm of forging stock, as measured by optical method (α + β) / β transformation point (Tβ) to 990 ℃.

In order to study the influence of the forging process on microstructure and mechanical properties of TC4 Titanium Alloy, forging stock will be divided into three sections, namely conventional forging (Tβ-60 ℃), near-β forging (Tβ-20 ℃) ​​and β forging (Tβ + 40 ℃) process test, deformation of 50%. Forging equipment for 3t free forging hammer. After forging, the process to get through three kinds of forging 900 ℃ × 1h / AC + 600 ℃ × 4h / AC dual heat treatment. After the heat treatment, the TC4 titanium alloy forgings intercept metallographic sample, tensile specimens and impact test specimens, the microstructure was observed under the microscope. Using image analysis software to complete and other microstructure parameters axis α phase content and secondary slice thickness α phase of quantitative statistics. The results showed that:

(1) TC4 alloy forged by α + β, near β and β forging three kinds of forging process after forging, respectively equiaxed structure, mixed structure and lamellar tissue.

(2) α + β forging, strength after forging close β and β forging TC4 titanium alloy bars fairly, but after forging and near α + β β β forging forging relatively high plasticity, but β forging TC4 titanium rod Best toughness. After nearly β forging TC4 titanium alloy bars show the best mechanical properties.

(3) tensile specimen fracture TC4 titanium alloy bars under three kinds of forging process showed a ductile fracture mechanism, α + β forging and near-β forging with deep and evenly distributed equiaxed dimples, and β forging alloy exhibits a more flat and elongated dimples.

3003 aluminum tubing range of applications

3003 aluminum tubing is the AL-Mn aluminum alloy, it is the most widely used in rust-proof aluminum, the strength of this alloy is not high (little higher than the aluminum industry) can not be heat strengthened, so the factory need to use cold working methods to improve its mechanical properties,in the annealed state has a high plasticity, in the half-cold hardening plasticity is still good, when the plastic work hardening is low, good corrosion resistance, good weldability, machinability bad.
3003 aluminum pipe formability, welding, and corrosion resistance are good.  Many componet parts the require need good formability ,high corrosion resistance and good solderability ,so use 3003 aluminum tubing is best choose.some products need to have a high strength alloy than 1XXX grade service work,

3003 aluminum pipe almost use in industry such as kitchen utensils, food and chemical products processing and storage means, tank transport of liquid products, tank, pressure vessels and piping general objects with sheet metal processing, heat sinks, makeup board, photocopier rollers, ship timber.

China’s aluminum exports will further increase

According to the futures through network “report, by the unexpected yuan depreciation, China the original expansion of exports of aluminum material will receive a further boost. China is the world’s largest producer of aluminum plate.

Goldman said that despite the decline in aluminum prices, many manufacturers have not cut out, partly because of the government’s subsidy policy. At the same time, China’s domestic demand is weak, has stimulated a large number of aluminum exports to the global market. 1-7 this year, China’s aluminum exports rose 28% year on year to record high. And this week the people’s money devaluation, aluminum market will face more supply, because people Za weakness will reduce domestic production costs.

Briggs BNP, an analyst at Paribas Stephen in Paris, said: “it is very clear that bad, which reduces the cost of domestic dollar denominated production.” LME this year three months aluminum fell 14% to $1589 per ton. According to the harbor intelligence data, in the Chinese devaluation people Za 1.9%, the average cost of production per ton of raw 2024 aluminum plate reduction of $12 to $1728. The company expects 10% against the dollar, people’s money, will further reduce the cost of $50 to $1678 per ton.
According to customs data, as of July this year, China exported 2870000 tons of aluminum and aluminum products this year, a record high. Harbor general manager Vazquez Jorge said in a report Tuesday: “the devaluation of the renminbi has restored the competitiveness of China’s exports.” “China’s structural economic growth slowdown, production capacity and production will be the main driving force for the decline in commodity prices.”

how many classifications of Aluminum pipes have?

Industrial pure aluminum aluminum content between 98.8-99.7%, but the pure aluminum material is too soft not have too much practical value, alloy aluminum products is based on pure aluminum group in general, the main alloying elements are copper, silicon, magnesium, zinc, manganese, minor alloying elements are nickel, iron, titanium, chromium, lithium and so on. Because of its high strength, light weight, easy processing, good appearance and corrosion-resistant properties, is used in many industries.

Aluminum alloy grades used by four digit naming alloy group ，in order to  the distinction between aluminum alloy content:

Aluminum Alloy Grade	main alloying elements
1XXX	Pure Aluminum (Al content of not less than 99.00%)
2XXX	Cu (Copper)
3XXX	Mn (manganese)
4XXX	Si (silicon)
5XXX	Mg (magnesium)
6XXX	Mg + Si (Mg + Si)
7XXX	Zn (zinc)
8XXX	Other elements

Different aluminum series grades have  differences performance  and applications , the DETECT-METALS  currently produces precision aluminum pipe primarily is  3XXX and 5XXX series, especially in 3003,3103,5049 and 5052, mostly because of its good corrosion resistance and formability, These aluminum pipes is widely used in heat exchangers. Aluminum places 6XXX series based mainly 6061,6082,6063,6005,6110, because of its high strength, easy machining, weldability and corrosion resistance, 6061 aluminum pipe extrusions used in many structural components .

In September this year, China Aluminum will reduce production of 650000 tons

In the news recently, the world’s largest aluminum pipe producer-Detect metals Aluminum said the company and other peers are still considering the reduce of production, following the last two years, 650000 tons of production was recuded, the company will in September this year to cut 200000 tons, so the aluminum price is expected to rise by the end of this year to about $2000 per ton.

For this year’s production plan, China Aluminum in a recent quarterly report said that this year will not restart aluminum smelting plant which has been closed in 2013, is considering the implementation of active maintenance capital expenditure management system, in order to optimize the maintenance of the original, is expected this year’s electrolytic aluminum production will be flat in 2014 of 3601000 tons.

China Aluminum said, plans to improve the construction of facilities in 2018 Mykolaiv aluminum plant, when the alumina production capacity will be increased from the current 1600000 tons to 1700000 tons.

Previously released data show that the second quarter of the 2024 aluminum pipe oxide production of 1818000 tons of alumina, according to the quarter rose 0.6%, an annual rise of 0.8%. Bauxite production reached 3223000 tons, 3.2% increase in quarterly and annual growth of 7.3%.

In the second quarter, the China Aluminum sales and average price fell: during the total production of its total output of 908000 tons, an increase of 0.8% in the quarter, but the sales volume by 5.1% to 880000 tons per season. The average price of the period to achieve a reduction of 7.7% to $2124 per ton, compared to the quarter.

Three new member companies join the Aluminum Association

The Aluminum Association announced the new member companies to join our group heiche surface technology; Phinix, LLC; Walter surface technologies. These companies are joined to the Associate Companies, the supply of North American aluminum sheet industry and goods and services company.

A new member of the increase came to an ongoing demand for growth of al. According to recent data from the Aluminum Association, the North American 3003 aluminum sheet industry in 25500000000, at 2014, the most 2006 pounds of aluminum shipments estimated. Compared with the new data show that the demand for 3.1% years increased to 2015 in April. From the 2009 baseline, the United States and Canada’s metal demand increased by nearly 40%.

“We are very pleased to welcome these new member companies,” said Heidi Block, President and CEO of al. “Our colleagues have brought a unique perspective to our work to help us serve a wider range of industries.”

How to clean stainless steel surface?

Note that scratch the surface of the washing does not occur, to avoid the use of bleach-containing composition and abrasive cleaning liquid, steel balls, grinding tools, in order to remove the washing liquid, at the end of washing, rinsing the surface with clean water.

Surface state
Washing

Easy to get rid of dust and dirt
Soap, washing detergent or weak with warm water

Labels and foil
With warm, weak detergent to scrub the adhesive composition with alcohol or an organic solvent

Fats, oils, oil pollution
With a soft cloth or paper neutral washing detergent or ammonia solution or special washing to dry after use drugs

Bleaches as well as various acids attached
Rinse immediately with ammonia or soda solution soak carbonate, after washing with neutral detergent or warm water

Organic carbide attachment
Soak in a hot neutral detergent or ammonia solution is then washed with a detergent containing weak ground

Fingerprint
With alcohol or organic solvents (diethyl ether, benzene), with a soft cloth and then washed with water

Rainbow pattern
Excessive use of detergent or oil caused by washing with warm water and mild detergent

Welding heat discoloration
With 10% nitric acid or hydrofluoric acid, ammonia or washing soda carbonate solution and then with light and handle, and then washed with water. Drugs may also be used for washing

Corrosion caused by surface contaminants
Washed with 10% nitric acid or abrasive detergents, drugs or the use of special washing

Stainless steel bending Notes

1. From unit size, the thicker the plate, the greater the force required to bend, and with the increase in thickness of the device when selecting bending bending force margin should be greater than the average thermal conductivity of stainless steel due to low-carbon steel poor, low elongation, resulting in deformation force required;

2. The next unit size, tensile strength, the smaller the elongation, the greater the force required to bend, bend angle should be larger with respect to the same thickness of the stainless steel bend angle is large, it should be Special attention will be bent or crack, the impact strength of the workpiece;

3. The design of the thickness and the bending radius corresponding to the case, based on experience, expand the size of a bend of the workpiece minus the sum of two right-angled edge thickness, designed to fully meet the accuracy requirements, expand the amount calculated according to the empirical formula simplify the calculation greatly improve production efficiency;

4.The greater the yield strength of the material, the greater the amount of spring back, to get bent parts 90 degree angle, the required pressure of the knife angle must design smaller, austenitic stainless steel in the bend with respect to there is a big deformed steel elastic recovery, so the pressure is relatively steel knife angle is smaller.

Recent steel prices continue to rise

     Recent steel prices continue to rise, construction steel, sheet metal up far beyond the 100 yuan / ton. In terms of profitability, steel profits also increased, since the early low-cost iron ore, steel prices and the recent pull up more than 100 yuan, into the black. But after prices continued to rise, the real needs are being tested. While the steel market rose in April, but the fact of the first quarter trade deficit also unable to change.

     Iron and steel industry in the class of excess industry come today, but also for large-scale investment before paying. Current national economic downturn under pressure, adjusting the economic structure, the economic downturn endurance enhancement, Li Keqiang speech recently said it would introduce some measures to steady growth, but will not introduce large stimulus, more decentralization reforms to activate the internal market economy energy, infrastructure construction, such as maintaining economic stability.

   

Aluminum divided into five categories

1.Brushed aluminum plate:  the process is divided into the main flow of degreasing, Sanders, washed three parts. In aluminum wire drawing process, need to repeatedly use sandpaper to scraped line in aluminum surface, a special anodized coating technology after the aluminum surface can form a coating layer of the metal component containing each of fine silk show clear marks, so that the metal in matte glow fine hair silk sheen.

2.Oxidation Aluminum plate: aluminum plate placed in the appropriate electrolyte solution (such as sulfuric acid, chromic acid, oxalic acid, etc.) as the anode, under certain conditions, and applied current role, were formed aluminum electrolysis. Anodic aluminum oxide, aluminum oxide thin layer formed on the surface to a thickness of 5 to 20 microns, hard anodic oxide films of up to 60 to 200 microns.

3.PS aluminum plate (also known as a printed advertisement aluminum zinc plate, newspaper board): the back of the printed pattern the aluminum plate.

4.Mirror aluminum plate: refers to treatment by a variety of methods rolling, grinding, so that the aluminum surface looke like the mirror .

5.Embossed aluminum plate also can be called aluminum embossing plate: below on the basis of aluminum plate, through a rolling process in a variety of patterns formed on the surface of aluminum products, the wide of the used this embossed aluminum plate, mainly used in the packaging, construction, walls, and so on.

what do i need to know when cutting Titanium alloy?

(1) Due to the small elastic modulus of titanium alloys, deformation of the workpiece clamped in the processing of deformation and stress, will reduce the machining accuracy of the workpiece; clamping force of the workpiece installation should not be too large, increase the auxiliary support, if necessary.

(2) All workers, with titanium fixtures or other devices must be clean contact; via cleaned titanium parts, oil or fingerprints to prevent contamination, or future may cause salt (sodium chloride) stress corrosion.

(3) Under normal circumstances when machining titanium, no ignition danger only when trace cutting, small chips cut have ignition combustion phenomenon. To avoid fires, in addition to a large number of pouring coolant should prevent the accumulation of chips in the machine, the tool to be replaced immediately after blunt or reduce the cutting speed, feed rate increased to increase the chip thickness. If the case of fire, you should use talcum powder, limestone powder, dry sand, and other fire-fighting equipment were extinguished, it prohibited the use of carbon tetrachloride, carbon dioxide fire extinguisher, not water, because water can accelerate the burning, and even lead to a hydrogen explosion.

5 tips you have to know to maintain aluminum sheets

In order to maintain the performance and appearance of aluminum sheet, also prolong the life of aluminum sheet, we are need to carry out regular maintenance of aluminum alloy sheet .now share the conservation Measures of the alloy aluminum sheet to you:

1, aluminum sheet during storage, prohibition together with chemical products and within humid storage.

2, aluminum sheet during transport, use tarpaulin cover, beware of snow intrusion.

3, aluminum sheet storage environment should be dry, bright, airy, non-corrosive climate.

4, aluminum sheet in the handling process, it is necessary to gently, beware bump caused by the appearance of bruising, affect the appearance beautiful.

5, aluminum sheet during storage,we proposed that the small standard aluminum sheet should be on the shelf , For large standard aluminum sheet the best storage method is use  the bottom with skids ,in order to  separated from the ground, and the ground distance is greater than 10 cm.

July national renewable aluminum ingots companies operating rate survey

Recently Zhuo record information on the more than 100 Hebei, Shandong, Shanghai, Zhejiang, Chongqing, Guangdong and other 12 regions of secondary aluminum alloy ingot production business started in July to conduct research,as can be seen nationwide in July subnational aluminum ingot production enterprises operating rate is uneven, where the north, east and other places more stringent environmental inspection, the overall operating rate of about 30 percent, the lowest operating rate in Tianjin where only 15% manufacturers generally reflect, currently only has production qualification standards and environmental protection equipment businesses to normal production, and due to demand and other factors operating at only 50 percent; and South, Southwest and other places, some small and medium manufacturing enterprises located in remote mountainous areas, environmental inspection the intensity is not strict, high overall operating rate. According to Cho Chong Research: July nationwide average of all domestic renewable aluminum ingots companies operating rate of about 41 percent, a decline of 10%.

July aluminum ingot industry off-season, but by the impact of this environmental crisis, renewable industry survival more difficult. This month domestic aluminum ingot GB ADC12 average price 14,115 yuan / ton, down 321 yuan from last month / ton; average price of aluminum ingot of non-standard ADC12 12,161 yuan / ton, last month fell 130 yuan / ton.

After the hotter weather, a general decline in the rain, but aluminum ingot manufacturers started production and procurement initiative has not improved. Spot aluminum prices fell again, GB more than the price of aluminum ingot aluminum based on the spot price, selling prices fell after. At the same time, in the off-season prices of aluminum ingots companies under production remained low. According to Zhuo record and statistics, there are aluminum ingot production qualification of renewable companies operating at only 20-60%, not regeneration aluminum ingot production qualification of enterprises affected by the environmental impact of substantially all of the shut down, the market is in a semi-closed state.

Aluminum Cleaner for Aircraft Detailing by Alcoa

There are a lot possibilities for plane detailing on the subject of aviation uses. 1 service we like when tying all of them out was an item by Alcoa Company. The merchandise is distributed by CLB Enterprises at Alcoa Company for aluminum polish in all facets of detailing. We put to use this on some museum items and observed the ease of use as we polished out an all aluminum plate T-33 the trainer version of your F-80 Korean War Vintage “Shooting Star.” It took close to 22 man-hours with Alcoa’s Aluminum Polish to complete this mission. We bid the task at 40-hours simply because frequently that is what it would consider with other brand names.

My agency, the Plane Wash Guys, has lots of go through with aluminum sharpening and shiny deliver the results. And who better to have confidence in than the producers of about 1/3 of many of the aluminum mined and recycled in the world. Alcoa has with stood the test of your time. Alcoa has also been instrumental around the legislation to demand citizens to recycle aluminum that is definitely important for thus many on the desired products we take with no consideration day-to-day. Whether it is a beer can, aluminum rail automobile, Boeing 747 or Apollo Space Craft, you’re able to bet it’s crafted with Alcoa materials.

We’ve tested these products and samples are despatched to all Depth Fellas Franchisees. All our groups concur this is actually a finest notched product or service indeed. We use this products following screening it on Aircraft and aluminum trim on motor vehicles, vans and boats. There exists no simple and easy tactic to clear aluminum and to make it shine; consult any Harley Davidson Motorbike enthusiast, plane owner, yacht operator or clearly show truck owner. There is certainly no painless way. Still considered one of the perfect products and solutions we’ve at any time seen is Alcoa’s Aluminum Polishes. Not merely would be the item spectacular, it’s politically accurate.

A number of will probably argue that Mother’s Polish is considered the greatest for bikes and we have now to concur Mother’s is a wonderful merchandise, but when utilizing giant amounts to carry out good sized surfaces, you will find a specific financial gain inspiration with our crew. Mother’s Polishes as you can imagine are great also. We thank Alcoa for licensing you’ll find it polish from it is really point out for the art, great tech Research and Progress Group, to deserving distributors just like CLB Enterprises so its on the market to our crew and aviation enthusiasts in a lower and truthful selling price. It is this amount of commitment to your sector put that keeps our team around the winner’s circle and Alcoa at the prime in their match. And it certainly saves the arms of an plane operator who really should polish out their plane, since God understands there is no effortless way. 2024 Aluminum plate can be described as good alloy for so lots of of mankind’s most prized possessions and innovations; through the wheels on your own hot rod to pieces and parts within the World’s greatest capabilities jet aircraft and it’s been for many years. Go for the correct aluminum polish and preserve your muscle tissue and time for flying. Assume on this.

Good News ,aluminum sheet promotion with lowest price from Detect-metals

To learn more:http://www.detect-metals.com/good-news-aluminum-sheet-promotion-with-lowest-price-from-detect-metals/